document number: 83631 for technical questions, contact: optocoupleranswe rs@vishay.com www.vishay.com rev. 1.9, 29-oct-10 1 optocoupler, phototriac output, low input current il440 vishay semiconductors description the il440 consists of a gaas infrared emitter optically coupled to a silicon planar triac chip with a non-zero crossing network. the two semiconductors are assembled in a 6 pin dual-in-line plastic package. the il440 can handle currents up to 100 ma rms. agency approvals ? ul1577, file no. e52744 system code h or j, double protection ? csa 93751 ? din en 60747-5-5 (vde 0884) available with option 1 ? bsi iec60950; iec60065 features ? 400 v blocking voltage ? 5 ma maximum trigger current ? isolation test voltage, 5300 v rms , t = 1 s ? isolation materials per ul94 ? pin compatible with optocouplers: - il440-4 moc 3021 - il440-5 moc 3022 - il440-6 moc 3023 ? compliant to rohs directive 2002/95/ec and in accordance to weee 2002/96/ec applications ? high current triac driver ? solid state relay ? switch small ac loads note (1) also available in tubes, do not put t on the end. 1 2 3 6 5 4 mt2 mt1 nc a c nc i179035_2 v de i179035 ordering information il440-#x0##t part number trigger current bin package option tape and reel agency certified/pack age trigger current, i ft ul, cul, bsi 5 ma 10 ma 15 ma dip-6 il440-6 il440-5 il440-4 smd-6, option 7 il440-6x007 - - smd-6, option 9 il440-6x009t (1) il440-5x009 il440-4x009t (1) vde, ul, cul, bsi 5 ma 10 ma 15 ma dip-6, 400 mil, option 6 il440-6x016 il440-5x016 - smd-6, option 7 - il440-5x017t il440-4x017 smd-6, option 9 il440-6x019t - - > 0.1 mm 10.16 mm > 0.7 mm 7.62 mm dip option 7 option 6 option 9
www.vishay.com for technical questions, contact: optocoupleranswe rs@vishay.com document number: 83631 2 rev. 1.9, 29-oct-10 il440 vishay semiconductors optocoupler, phototriac output, low input current notes (1) stresses in excess of the absolute maximum ratings can cause pe rmanent damage to the device. functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. exposure to abs olute maximum ratings for e xtended periods of the time ca n adversely affect reliability. (2) refer to reflow profile for soldering conditions for surface mounted devices (smd). refer to wave profile for soldering condit ions for through hole devices (dip). absolute maximum ratings (1) (t amb = 25 c, unless otherwise specified) parameter test condition part symbol value unit input reverse voltage v r 5v forward current i f 60 ma surge current p.w. < 10 s i fsm 3a power dissipation p diss 100 mw junction temperature t j 100 c output peak off-state voltage il440-4 v drm 400 v il440-5 v drm 400 v il440-6 v drm 400 v on-state rms current i d(rms) 100 ma peak surge current t p 10 ms i fsm 1.2 a peak on-state current t p /t = 0.01 100 s i drm 2a power dissipation p diss 300 mw junction temperature t j 125 c coupler isolation voltage t = 1 s v iso 5300 v rms creepage distance 7mm clearance distance 7mm isolation resistance v io = 500 v, t amb = 25 c r io 10 12 v io = 500 v, t amb = 100 c r io 10 11 total power dissipation p tot 330 mw storage temperature range t stg - 55 to + 125 c ambient temperature t amb - 40 to + 100 c junction temperature t j 100 c lead soldering temperature (2) 2 mm from case, t < 10 s t sld 260 c
document number: 83631 for technical questions, contact: optocoupleranswe rs@vishay.com www.vishay.com rev. 1.9, 29-oct-10 3 il440 optocoupler, phototriac output, low input current vishay semiconductors notes (1) minimum and maximum values are testing requirements. typical values are characteristics of the device and are the result of eng ineering evaluation. typical values are for information only and are not part of the testing requirements. (2) off-state output terminal voltage (see table 1.) notes (1) according to din en 60747-5-5. this optocouple r is suitable for safe elec trical isolation on ly within the safety ratings. compl iance with the safety ratings shall be ensured by means of suitable protective circuits. (2) the device is used for protective separation agains electrical shock within the maximum safety ra tings. this must be ensured by protective circuits in the applications. electrical characteristics (1) (t amb = 25 c, unless otherwise specified) parameter test condition part symbol min. typ. max. unit input forward voltage i f = 50 ma v f 1.25 v reverse voltage i r = 10 av r 5v junction capacitance v r = 0 v, f = 1 mhz c j 50 pf output (2) off-state voltage i drm = 500 na il440-4 v d(rms) 400 v il440-5 400 v il440-6 400 v peak on-sta te voltage i tm = 100 ma, i ft = 30 ma v tm 1.5 3 v trigger current 1 v t = 6 v, r l = 150 il440-4 i ft1 15 v trigger current 2 il440-5 i ft2 10 v trigger current 3 il440-6 i ft3 5v critical rate of rise of off-state voltage i f = 0, v d = 0.67 v drm dv/dt cr 50 v/s critical rate of rise of on-state current commutation i f = 30 ma, v d = 60 v rms dv/dt crq 0.13 0.25 v/s coupler holding current i f 10 ma, v s 3 v i h 1ma maximum safety ratings (1) parameter test condition symbol min. typ. max. unit input (2) forward voltage i s, input 130 ma output power dissi pation p s, output 300 mw safety and insulation ratings parameter test condition symbol min. typ. max. unit climatic classification (according to iec68 part 1) 55/100/21 pollution degr ee din vde 0109 2 comparative tracking index cti 175 v iotm 8000 v peak v iorm 890 v peak insulation resistance at 25 c v io = 500 v r is 10 12 insulation resistance at t s v io = 500 v r is 10 9 insulation resistance at 100 c v io = 500 v r is 10 11 partial discharge test voltage method a, v pd = v iorm x 1.875 v pd 1669 v peak p so 500 mw i si 250 ma t si 175 c
www.vishay.com for technical questions, contact: optocoupleranswe rs@vishay.com document number: 83631 4 rev. 1.9, 29-oct-10 il440 vishay semiconductors optocoupler, phototriac output, low input current note ? as per iec60747-5-5, 7.4.3.8.1, this optocoupler is suitable for safe electrical in sulation only within the safety ratings . compliance with the safety ratings shall be ensured by means of prodective circuits. package dimensions in millimeters package marking clearance distance standard dip-6 7 mm creepage distance standard dip-6 7mm clearance distance 400 mil dip-6 8 mm creepage distance 400 mil dip-6 8 mm safety and insulation ratings parameter test condition symbol min. typ. max. unit i178004 0.25 typ. 2.95 0.5 3.555 0.255 0.8 min. 7.62 typ. 0.85 0.05 2.54 typ. 1 min. 0.5 0.05 6.4 0.1 8.6 0.1 pin one id 6 5 4 1 2 3 18 3 to 9 7.62 to 8.81 4 typ. iso method a 0.5 0.05 8 min. 0.51 1.02 7.62 ref. 9.53 10.03 0.25 typ. 0.102 0.249 15 max. option 9 0.35 0.25 10.16 10.92 7.8 7.4 10.36 9.96 option 6 8 min. 7.62 typ. 4.6 4.1 8.4 min. 10.3 max. 0.7 option 7 18450 21764-91 il440 v yww h 68
legal disclaimer notice www.vishay.com vishay revision: 12-mar-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products no t expressly indicated for use in such applications do so at their own risk and agr ee to fully indemnify and hold vishay and it s distributors harmless from and against an y and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale , including attorneys fees, even if such claim alleges that vis hay or its distributor was negligent regarding th e design or manufacture of the part. please contact authorized vishay personnel t o obtain written terms and conditions regardin g products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu.
|
